Digi M10 Technical overview and Guida di Installazione Scaricare il pdf (Pagina 55)

S6 Installation Guide50

Attaching the Outer Side Covers

After cables are in place, install the outer side covers (outer side covers must be installed before modules).

To attach the Side Covers:

1 Before attaching the outer Side Covers, make sure to route the single Ethernet (workstation) cable and the AC supply to the

power strip across the Rear Panels and down through the gap to the right (or left) of the outer Rear Panels (see Figure 27).

2 Make sure power and Ethernet cables are not in the way, then set the panel into the side bracket so that its tabs hang on the slots

on the mounting plate as shown in Figure 28.

Figure 27. Gap for power strip AC and workstation Ethernet

Figure 28. Attaching the left Side Cover

1 2 ... 50 51 52 53 54 55 56 57 58 59 60 ... 81 82

S6 Installation Guide 1
Legal Notices 2
Contents 3
S6 Installation Guideiv 4
Part I: Introduction 5
Chapter 1: Introduction 6
Overview of Installation 7
What’s Included 7
Activation and Registration 8
About This Guide 9
About www.avid.com 9
Master Section Modules 10
Channel Modules 11
Knob Module 12
Display Module 12
Module Layout 13
S6 Installation Guide10 15
Part II: Frames 16
Chapter 3: Assembling Legs 18
Attaching the Back Beam 19
Attaching the Front Beam 20
(Not to scale) 21
Attaching the End Shelves 22
Leveling the Leg Frame 22
How to Proceed 23
Before You Begin 24
Frame Chassis Kit Components 25
Assembling the Chassis 26
S6 Installation Guide22 27
M3x6 SEMS (7760-30025-01) 28
#1 Phillips 28
Important 29
Attaching the Back Feet 30
Leveling the Chassis 32
Attaching the Bolster 33
M5x12 FHCS 34
M5x8 SHCS (7760-30593-00) 35
Installing Side Covers 36
Part III: Modules 38
Overview 40
Installing the Power Strip 41
Ethernet Switch” on page 40 43
6-Chassis Systems 44
7-Chassis Systems 44
9-Chassis Systems 44
S6 Installation Guide40 45
Installing PSUs 46
To connect power to PSUs: 47
12 3 4 512 3 4 5 49
12 3 4 5 49
12 3 4 512 3 4 5 12 3 4 5 50
12 3 4 5 12 3 4 512 3 4 5 51
7- and 9-Chassis Systems 52
S6 Installation Guide48 53
To attach the Side Covers: 55
M4x14 FHPH 56
#2 Phillips 56
Chapter 6: Installing Modules 58
Installing Modules 59
S6 Installation Guide56 61
Automation 62
Installing the Master Module 63
Setting the Touchscreen Angle 64
Installing Fill Panels 65
Installing Display Modules 65
Gigabit 66
Ethernet RJ45 66
S6 Installation Guide62 67
Chapter 7: How to Proceed 68
Installing Compression Panels 69
Installing T Strips 70
Figure 40. Upper Rear Panel 71
Updating S6 System Software 72
Configuring the S6 System 73
Part IV: Appendices 74
Removing Modules 76
Disassembling a Frame 77
Appendix B: Compliance 78
Australian Compliance 79
Canadian Compliance 79
CE Compliance 79
Safety Compliance 80
Korea Class B EMC Compliance 80
S6 Installation Guide76 81
Technical Support (USA) 82
Product Information 82

Commenti su questo manuale

Nessun commento

Digi M10 Technical overview and Guida di Installazione Pagina 55

Commenti su questo manuale

Prodotti e manuali riguardandi Networking Digi M10 Technical overview and